Go
All Results Based on Water Viscosity.

N992

Pump housings and gears are made of top quality bronze, shafts are 303 stainless steel. Bearings are designed of high performance carbon-graphite material selected for wear resistance and long service life.

Gear pumps are positive displacement pumps. Each shaft revolution displaces a definite amount of liquid  relatively unaffected by the back pressure in the discharge line. Shaft speed and flow are directly proportional.

Recommended pressure limits are 100 PSI for water and non-lubricants, 150 PSI for oil and other lubricants. The maximum shaft speed is 1750 RPM.

FEATURES

  • Rugged Corrosion Resistant Bronze Construction
  • Compact Close-Coupled Design
  • Stainless Steel Shafts
  • Durable Bronze Helical Gears Provide Quiet Operation
  • Process Lubricated Carbon Graphite Bearings
  • O-Ring Cover Seal For Maximum Leak Protection
  • Lip Seal or Mechanical Seal

Easy Field Assembly to a Variety of Motor Frames - For Typical DC Motor Pump Units - see N992 DC

- For Compact AC Motor Pump Units  see Close Coupled Bronze Adapterless Rotary Gear Pumps - For Danfoss Hydraulic Motor Driven Pump Units - See Adapter 9960 For Bonze Pedestal Pumps - See Model N2000 For Close-Coupled Ductile Iron Pumps - See Model C992

LIQUIDS & TEMPERATURES

These pumps are suitable for all liquids that are compatible with bronze. Most common liquids are water, oil, and mild chemicals in the pH range of 4 to 11. Viscous liquids require reduced shaft speeds of 1150 RPM or lower. (Consult factory.) Liquids containing solids, abrasives, powders, or paint pigments are definitely not recommended for gear pumps. If abrasives are unavoidable, use a very low shaft speed. See price book for the recommended liquid temperature range of lip and mechanical seals. If more extreme temperature conditions exist, factory should be consulted. Freezing of water-filled pumps can cause damage and must be avoided. Oils at low temperatures are very viscous requiring a lower speed or extra power.

SUCTION LIFT

As a general rule, the suction lift should be kept at an absolute minimum by placing the pump as close to the liquid source as possible. A gear pump in new condition can lift 20 feet of water in the suction line. A foot valve (preferably with built-in strainer) is recommended at the beginning of the suction line. For a first startup, the pump should be primed to avoid dry running. Minimum size of the suction pipe is the size of the pump inlet port. For longer suction lines (over 3 feet) or for viscous liquids, the pipe should be at least one size or two sizes larger than the pump inlet port. If the discharge line contains any throttling devices such as a shut-off valve, a spray nozzle or other restrictive device, it is necessary to have a relief valve in the system, which returns the liquid to the suction side or to the tank. The relief valve is also available as part of the pump itself (R-model pumps). However, built-in relief valves are only good for intermittent service. If used continuously, the pump will overheat. A built-in relief valve is strictly a safety device against overpressure. It will not work successfully as a pressure or flow control device. For this purpose a separate relief valve in the pressure line must be used. Unless otherwise specified, the pump motor unit is supplied by the factory for shaft rotation counterclockwise from shaft end. Reversing motor will reverse “in and “out” ports and also requires changing relief valve location. The relief valve is always on the inlet side of this pump series. The factory pressure setting is 50 PSIG. To increase pressure, turn the relief valve adjusting screw in a clockwise direction.

PERFORMANCE

N992 C992 Curves

EXPLODED VIEW & PARTS LIST

N992 Exploded

N992 SERIES SPEC SHEET Copy

N992

 

 

Parts List Sheet1

Adapter Kids Sheet1

DIMENSIONS

N92 R OUTLINE

N992 Dim Copy

N992E