Go
All Results Based on Water Viscosity.

70P

Oberdorfer™ centrifugal pumps have a single rotating metal impeller. Liquid enters at the center and is thrown outward radically by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient, pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently a relief valve is not required.

The liquid flow varies directly as the pump speed--the higher the speed the greater the flow. Horsepower required varies directly as flow and pressure. Maximum horsepower is required with a wide open discharge line. This is the point of maximum flow. With a throttled discharge, the flow decreases at a greater rate than the pressure increases thereby requiring less horsepower at the higher pressures. This is known as an “unloading” feature of the pump.

Silent, efficient, centrifugal pumping is ideal for convenient equipment location in offices, laboratories, public areas, and living quarters. Long trouble-free service life has made centrifugal pumps acceptable for industrial uses or wherever clean or contaminated liquid compatible with bronze is to be transferred or handled.

The 70P centrifugal pump has an external ball bearing isolated from the liquid being pumped. The ball bearing is greased and sealed for life, requiring no maintenance.

FEATURES

  • Rugged Bronze Construction
  • Quiet Operation
  • O-Ring Housing seal eliminates gasket problems
  • Mechanical Seal - Carbon/Ceramic
  • NItrile - standard
  • Fluoroelastomer (S10) or Polytetrafluoroethylene (PTFE) (S11) - options
  • Designed for Pulley Drive
  • Heavy Duty Integral Steel Shaft and Ball Bearings
  • Handles Contaminated Liquids
  • No bearing lubrication required
  • For Close Coupled Style, see Model 700

DRIVE

The pedestal centrifugal pumps can be direct driven by electric motors at either 3450 R.P.M. or 1725 R.P.M. Performance for both speeds are shown in the curves above. The 70P pedestal centrifugal pump can be pulley driven at any desired intermediate speed.

LIQUIDS & TEMPERATURES

Bronze pumps are suitable for most common liquids in the PH-range from 4 to 11. The temperature limit for bronze pumps is 212o F, higher temperatures are possible with Fluoroelastomer or Chemlon seals. If in doubt, consult with factory.  Because centrifugal pumps are more efficient at higher shaft speeds, pumping of viscous or thick liquids is difficult. It is possible to lose as much as 40% pump performance when attempting to pump liquids of viscosity equal to S.A.E. 30 oil at room temperature. S.A.E. 30 oil at room temperature has a viscosity of 2000 Saybolt Seconds Universal. More viscous liquids are not recommended for centrifugal pumps.

SUCTION LIFT

This centrifugal pump is not self priming. Normally these pumps must be installed below the liquid level so that the liquid flows to the pump by gravity. However, if a foot valve is used at the beginning of the suction line and all air is bled from the suction line and pump by careful manual priming, these pumps will lift liquid on the suction side up to 15 ft. Such a system is only as positive as the ability of the foot valve to seal and keep the suction line and pump full of liquid. If the foot valve should leak, the pump will not prime.

PERFORMANCE

70P CURVE

EXPLODED VIEW & PARTS LIST

70P EXPL REVISED70P Chart Rev _5_06_WE_REAL Sheet1

DIMENSIONS

70P DIM

SHAFT SEAL OPTIONS 

Mechanical Shaft Seals have Nitrile rubber components (212oF max) as standard. For temperatures up to 400oF a Fluoroelastomer seal must be selected by adding code S10 to the pump number. To handle strong solvents and chemicals (compatible with bronze), a Chemlon seal (500oF max) must be specified by adding code S11 to the pump number. In most instances, Fluoroelastomer and Chemlon seals are not field interchangeable with the standard Nitrile seals. Call factory for details.